All Products

Classic Mini Pickups had a one-piece headlining frame with the canopy glued and stapled to it. Cream Crackle was used on early models and the light grey was used during the 1970's

Headliner canopy kit in original cream-crackle for Riley Elf and Hornet. Includes C-post trim panels. Ref: HL3005A, HL3005P, HL3005W, HL3005C.

One-piece headlining canopy held place by six specials stays. Ref: HL3012, HL3012A, HL3012P, HL3012W.

One-piece headlining canopy, held place by six specials stays (not included). Ref: HL3012, HL3012A, HL3012C, HL3012W.

Headliner kits for Mk1 classic Mini saloons (sedans) 1959-1967. Ref: HL3000, HL3000A, HL3000C.

Headliner kits for Mk1 classic Mini saloons (sedans) 1959-1967. Ref: HL3000, HL3000W, HL3000P.

Classic Mini saloons (sedans) 1967-70 had a two-piece headlining frame with the canopy glued and stapled to them. Ref: HL3010P HL3010W.

Headliner kit for classic Mini saloon (sedan) two-piece headliner frame, as used 1967-1970. Ref: HL3010A, HL3010C.

Two-piece headliner kit for 1960-1970 classic Mini Traveller. Ref: HL3020, HL3020A, HL3020P, HL3020C, HL3020W.

One-piece headliner canopy kit for classic Mini van models

One-piece headliner canopy kit for classic Mini van models; white.

Complete kit to replace cracked or missing heat shields on twin HS2 setup. Black powder-paint finished. Includes interconnecting bridge, two shields and springs. Ref: MSSK008, SIE0041.

A complete heat shield kit in highly-polished stainless for twin HS2s. Includes two shields, bridge, and springs. Ref: MSSK1005, SIE0041SS.

Heat shield kit in black for twin HS4 (1.5'') carb set.

Heat shield kit in stainless for twin HS4 (1.5'') carburetor set. Ref: MSSK1006, SIE0122SS.

All-metal heater air duct as used on pre-1966 models, welded to the engine side of the front panel. Ref: 24A1301.

Heater cable as used on late-model classic Minis with in-line heater control valve. Loop end; 31'' length of inner cable. Ref: JFF10003.

As-original early classic Mini heater control cable; small black Bakelite knob with ''Push Heater'' embossed in white letters. Ref: 14A9988.

Reproduction of the Mk1 classic Mini heater cable. Black plastic knob with ''Push Heater'' embossed in white letters. Ref: 14A9988, 14A9988MS.

Push-pull heater control cable for classic Minis Mk2-onward, up to about 1984. Ref: CHM373, 24A2738.

Heater control cable for 1997-2000 MPi classic Minis. Outer sheath is 19'', with a loop at the end. Ref: JFF100910.

Special heater cable as used on SPi classic Minis only. Hook/loop end with 42'' inner cable.

Heater control valve that mounts on the rear (flywheel) end of the cylinder head; as used on classic Minis 1964-1988. Ref: ADU9102, ADU9102MS, 88G601.

In-line heater control valve, for classic Minis models from 1989 until SPi (single-point injection). Ref: JJB10011.

In-line heater control valve for classic Mini MPi models; attaches to the heater box. Ref: JJB100260.

Replacement metal outlets to repair a JEF10005 late heater core. Ref: JEP10008.

Replacement plastic outlets to repair a damaged heater core. Remove the metal retaining plate and replace the leaking or broken outlets with new ones. The plastic part only is supplied.

Plastic end with 5/8'' hose outlets on right-hand side, fits classic Minis 1984 to mid-1991. Aluminum matrix. Ref: BAU5043.

Heater core for classic Minis 1991-on. Plastic tank with 5/8'' hose outlets on left hand side. Ref: JEF10005.

Heater core (matrix) for Mk1 classic Minis with recirculating-type heater. Ref: 17H2096.

Heater core (matrix) for many Mk1 and Mk2 classic Minis, with opposite outlets with a 4'' spacing measured between the pipes. Ref: 17H8608.

Heater core for Mk3, 1970-1984 classic Minis. Diagonally-placed outlets for 0.50'' hose; made with a modern aluminum core.

Classic Minis with no heater will need to have the outlet on the cylinder head blocked off with this plate. Ref: 2A180, 2A0180.

A more durable and flashier version of the heater valve blanking plate, made of stainless steel. Ref: 2A180, 2A180SS, 2A0180SS.

Cable anchor as required by some early classic Mini heater control valves. Ref: 24G1482K.

Small stud to secure heater valve or blanking plate to cylinder head. Ref: 53K402, 53K0402.

1/2'' diameter water outlet for flywheel end of the cylinder head. Use in place of the heater valve. Ref: FOR108, FOR108A.

Billet aluminum alloy 5/8'' diameter heater outlet fitting for flywheel end of the cylinder head. Used from 1990-on in conjunction with the inline heater control valves. Ref: 12G2534, 12G2534A.

Heel board patch for classic Mini Van and Pickup models.

Vertical panel at the rear of the classic Mini Saloon (sedan) floor section, to which the front of the rear subframe is attached. Ref: 14A8160, MS51, HMP44108.

Complete Heritage heel board panel, as used at the rear of the classic Mini Saloon floor and to which the rear subframe is attached.. Ref: HMP441008, HMP441008/HTG.

Classic Mini Saloon (sedan) half-heel board repair body panels, made by British Motor Heritage. Ref: HMP441006, HMP441007, HMP441006/HTG, HMP441007/HTG.

The British Motor Museum can provide you with a certified copy of your vehicle's entry in the original factory ledger, showing your car's specification as it left the production line.

Chrome, hex head screw for the license plate light used on Mk1 and Mk2 classic Minis. Fits 56790 lamps. Ref: 17H5385.

Pair of genuine Hi-Lo aluminum strut extensions required for the rear of the classic Mini. Ref: SSS0014K, HILO-01.

Genuine U.K.-made Hi-Los are adjustable length struts that allow the classic Mini to be lowered or raised in each corner to achieve different ride height and corner weights. Ref: HILO, HI-LO, SSS0015K.

Stainless heat shield/linkage plate for HIF carburetors; will never rust! Ref: 3A0035, FOR021, CAM4942.

Pivot pin for float in HIF carbs; includes washer. Ref: WZX1258, WZX1450.