All Products

Reproduction wiper arm in the sixties design; parks to the right when stopped. Stainless material. Ref: 13H5626, SEL0149.

11'' stainless steel wiper blade to fit 5.2mm arm as used on classic Minis up to 1990. Ref: GWB223, GWB0223, GWB811.

10'' stainless steel wiper blade assembly. Fits 5.2mm straight bayonet wiper arm on classic Minis to 1990. Ref: GWB202, GWB0202, GWB219.

10'' stainless steel wiper blade assembly. Fits 5.2mm straight bayonet wiper arm, as used up to 1990. Ref: GWB219.

Black wiper blade to fit all classic Minis 1990-2000 with hook-type wiper arm. Ref: GWB911, GWB911MS, GWB199.

U.K.-made 11'' stainless steel wiper blades to fit only 13H5627 or 13H5630 wiper arms. Ref: GWB220.

Early classic Minis with a squared wiper motor body would use this brush set.

Kit that allows Classic Mini windshield wipers to operate with an intermittent delay. Ref: MSSK2005.

Mounting kit for Mk1 and Mk2 classic Mini and Mini Cooper wiper motors; includes bushings, special studs, nuts and washers. Ref: 743176KIT, 743176, WPR300.

Clip-in self-parking switch as found in classic Mini two-speed wiper motors. Use with motor numbers having D-prefix.

Metal strap in upgraded stainless steel with rubber gasket for installation of most round-body (2-speed self-parking) wiper motors after 1968. Ref: 37H4836, BHA4790, 54701783, 54704511.

Round body two-speed wiper motor as found on classic Minis from about 1968-on. Ref: LRW110, GXE7708, 37H8221.

Replacement round-body two-speed wiper motor as found on classic Minis from about 1968-on; includes gear and drive cable. Ref: LRW110, GXE7708, GEU7708, 75664.

This is the spiral wound cable that is in the wiper rack tubes. Requires cut to length; uncut size 59.06" (150cm).

This kit supplies all three pieces and the special nut which is now otherwise obsolete; tailored to fit Mk3 classic Minis with 2-speed wipers.

Wiper rack tube set as used on Mk1 and Mk2 classic Minis. Includes special nut not otherwise available.

Classic Mini wiper and washer switch that mounts on the right-hand side of the steering column; five wire pin plug. Ref: 35485, BAU5346, SQB116.

Column-mounted windshield wiper switch as fitted to MPi classic Minis 1997-on. Ref: XPE100420PMP.

Chrome 6-sided nut to fit wiper wheel box. Some classic Minis used an 8-sided nut, so check before ordering. Ref: 153510, 37H6316.

Mk1/Mk2 chrome-on-metal wiper bezel kit. Ref: 37H6042C.

Chromed metal wiper plinth kit for classic Minis Mk3 and later. Ref: 37H7201C.

Includes one upper and one lower hard-rubber spacer; designed from Mk3-on classic Minis, but the lower one can be shortened for Mk1 and Mk2 models. Ref: 37H7201, 37H7201MS.

This is the correct wiper wheelbox for Mk1-2 classic Minis, with 22 teeth on the internal gear. Same as Lucas 72851. Sold each, supplied less chrome nut.

Wiper wheelbox as fitted to classic Minis after Mk2; 32-tooth gear about 1.5'' in diameter. Ref: 37H7200, 72872.

Wiper/washer stalk switch for left-hand drive classic Minis 1984-89. Mounts on right-hand side of column. Ref: 30446, 37H8286, SQB167.

Wiper/washer stalk switch for right-hand drive classic Minis 1976-84. Mounts on left side of column. Ref: 30444, 37H8285, SQB190.

This is the small wire circlip that is compressed when the joint is installed on the shaft. Ref: 37H8706, 17H8596, 22G2688.

Female wire terminal, 3/8'' lucar crimp-on connector. Ref: CWB130, 54942079.

Socket and wiring pigtail for front turn indicator lamps for 1997-2000 MPi Rover classic Mini. Ref: XBD100671, XBD100670PLUG.

Proper-looking wire clamp for the classic Mini fresh air heater inlet hose. 3.5'' diameter. Ref: HCS156.

Fits around the stem of the damper to prevent the damper from dropping out of the dashpot cover. Fits SU HIF carburetors.

Original factory patterns were used to create this wiring harness for the '59 - 62 850 & Austin 7. Original colored wires with cloth wrapping.

Complete wiring harness for the 1960-62 Van & Countryman. Made to original patterns with proper wire colors and fittings, but modified for used with alternator.

Complete braided wiring harness fo 1963-1964 Cooper S, with generator and oil filter light switch.

Complete harness for 1963-67 Mk1 classic Mini 850 Super, Deluxe and Cooper models with 3-gauge center pod.

Wiring harness for 1964-67 classic Mini models with key start, 3-gauge center cluster, generator and oil filter light. Cloth braided. Ref: 5L503, 305MAIN, 325.

Complete wiring harness that fits Mk2 Cooper S with generator; braided black cotton covering with yellow flashes. Ref: 327, 5L691, WL327.

Complete harness that fits Mk2 Cooper S with alternator; braided black cotton covering with yellow flashes. Ref: 327ALT, 5L692, 5L0692, WL307, WL327-ALT.

Original factory patterns were used to create this complete wiring harness for the 1972-1975 classic Mini Clubman. This model was equipped with alternator, but no tachometer.

Original factory patterns were used to create this wiring harness for the 1972 to 1975 Mk3 classic Mini 1000. Ref: AN111C, 5L1331.

Wiring harness for Mk3 Mini Pickup or Van 1972-1975, center speedometer only. Wrapped in grey vinyl, as original, with original color wires and connectors.

Original factory patterns were used to create this complete wiring harness for the 1977-1980 Mk4 Canadian 1000. Ref: AN143.

Main and dash wiring harness for 1978-1979 classic Minis with 3-gauge center pod; for models with no side marker or fog lamps. Ref: AN124, WLAN124.

Main wiring harness for the first Minis with pre-engaged starters, approximately 1985-1988. Ref: HAM4385.

Main (front) wiring harness, for classic Minis 1989-on with servo. 2/3 clock, dim-dip relay.

Main wiring harness for single-point injection (SPi) classic Minis fitted with dim-dip relay, approximately 1992-1996. Ref: YMC11986.

Wiring harness for classic Minis with pin-type rocker switches and driver-side binnicle, inertia starter. Ref: AN128.

Complete wiring harness for the UK-made Austin Mini Moke, 1964-66 approximately. Made to original patterns with proper wire colors and fittings, but modified for used with alternator.