All Products

Cable as found on Mk1 classic Minis, typically with twin carbs. Black plastic knob, marked ''CHOKE'' and ''LOCK''. Ref: 21A1204MS, 21A1204.

Choke cable for most late classic Minis, with international symbol for ''choke'' on the end; will fit all classic Minis up to about 1990. Ref: 21A2329, NAM6834.

This is the nut found on Mk3-on classic Minis, and is not the same thread as the 6-sided nut used on Mk1-Mk2 Minis.

This is the full-width chrome finisher strip that clips to the lower dash tray edge. Ref: 14A8009.

Oval chrome metal trim strip that surrounds the three center-mounted gauges on classic Mini Deluxe/Cooper models.

Circlip that locks the first motion shaft bearing 13H6080 outer race into the flywheel housing. Ref: 2A3643.

Large circlip that retains the single roller main first motion bearing in place. Fits 4-synchro remote and rod change transmissions.

Circlip, or stop ring, around the AAU1365 double ball bearing on the mainshaft.

Circlip, inner race, outer end of 1st motion shaft. Used with 13H6080 bearing. Ref: CCN010, CCN0110.

Internal circlip, locates the bearing in 3-synchro laygear. Ref: 22G278, 22G0278.

Circlip that fits the larger ADU6033 bearing that was used in the Metro Turbo engine.

Retaining circlip for the reverse lever-to-case on remote shift transmissions.

Metal clamp for Petroflex-type braided fuel hoses; fits all .25'' bore hoses.

Set of three stainless steel band exhaust clamps to fit big-bore LCBs. Ref: MMKT0176, GEX175, GEX200.

Set of three stainless steel band clamps to fit standard bore LCBs. Ref: MMKT0177, SIE0414, GEX178.

This band clamp with stud attaches the fuel pump to the mounting bracket on the rear subframe. Ref: 21A632, 21A0632.

Front downpipe clamp that fits to the bracket (GEX7526) on gearbox. Ref: GEX7053.

Exhaust manifold to downpipe clamp; includes proper brass nuts and support washers. Ref: GEX7046.

Small clamp to fit FAM2807 rubber oil pressure gauge hose.

Metal band clamp for large end of steering rack boot. 2'' diameter to fit OE steering racks. Ref: BMK924A, STR0070, GSV1153.

Metal band clamp for small end of steering rack boot. Ref: GGT1117, STR0071, GSV1153.

In addition to the famous race and rally cars, coachbuilt conversions and highly modified saloons and commercials, Keith Mainland looks at overseas Mini and Moke production and the many factory-produced limited edition Minis.

Upper tail light lenses in clear with amber and red bulbs for converting the rear of a Mk4-on classic Mini to a customized clear-lens look. Includes parts for both sides.

Clevis pin with nylon bushing to fit the brake pedal on 1989 and later classic Minis with the horizontal brake master cylinder.

Clevis pin for the lower pivot end of the clutch arm. Ref: CLZ628, CLZ0628.

Clevis pin used in conjunction with door check arm ADA5671, on all classic Minis with roll-up windows from 1970 to 2000. Ref: CLZ412, CLZ0412.

Clevis pin to connect the master cylinder pushrod to the pedal; works for brake or clutch. Ref: CLZ512, CLZ0512.

Clevis pin connecting the clutch push rod to the clutch arm, as used on both the Verto or pre-Verto clutch. Ref: CLZ518, CLZ0518.

Gunson's Clickadjust makes valve adjustment quick and straightforward; settings and adjustments are spot-on accurate. Ref: G4094, MSA1001, CLIKADJUST.

Small plastic socket clip for pins on the reverse side of body badges. Ref: GFK7514, GHF1531.

Clip to retain the rubber seal on the classic Mini boot lid (to 1989) or the rear doors of the classic Mini Traveller and Van. Ref: 14A6585, 14A6585KIT.

Clip under front floor to secure fuel and brake lines, used from 1959-1990. Weld in place beside floor pan footwell and tunnel; use two (2) per car.

This bendable metal tab is spot-welded to the underside of the floor to locate the brake and fuel lines. Use three (3) per side, total of six (6) per car.

Special clip used to secure the brake pipe that crosses the front of the front subframe. Ref: 11K9181, KYC100070.

Choke cable clip for classic Minis from 1987 to 1991. Ref: ADU5065, SBF10027, SBF10031.

This clip locks the choke cable to the linkage plate on the HIF6/HIF44 linkage plate. Ref: CZK6491.

Clip that attaches the chrome finisher strip (14A8009) to the lower dash tray edge.

Small e-clip to connect the door opening remote control rod plus the lock control mechanism on roll-up window doors.

Plastic clip commonly used by Rover for all interior car trimming. Ref: GFK7509, GHF1222, GHF1220, CZK3631.

Clip retains Mk3 window scraper and also door pocket trim. Ref: ADH3809.

Clip for Mk1 Austin Mini bonnet badge 24A71. Ref: PFR108, PFR0108.

Small spring clip to receive the mounting screw of ''beehive'' front indicator lamps. Ref: GHF711, AK606021.

Metal bracket that clips to the headlight bucket assembly and serves as the anchor point for the chrome headlight bezel. Ref: 37H7421, 37H7421A.

Clip to attach inner guide found on all classic Mini roll-up window doors. Ref: EYC10048, AAU8399.

Small wire bow-tie clip to retain the oval chrome trim on the plastic gauge pod for Deluxe and Cooper models with center guage location. Ref: 14A9796.

Plastic clip to retain radiator fan switch in SPi (single-point injection) classic Minis only. Ref: KTP9002.

Black-oxide clip commonly used for the external body seam covers and the roll-up window door inner felt seals. Ref: GHF1560, GFK7515.

Anti-rust stainless steel version of the classic Mini seam cover clip. Ref: BMP128, BMP0128, GFK7515, GHF1560, BMP128MS.