All Products

Boot/trunk lid made in the exterior shape as used on the late Mk1 and Mk2 classic Minis, with full interior metal skin panel to finish off the loading area. Ref: 8G9270MS, 8G9270.

Classic Mini Mk1-2 boot lid, as updated in 1970 to the larger license recess of the Mk3 design. Ref: BMP339, BMP339/HTG, BMP0339.

Reproduction boot lid made in the Mk3-on exterior shape, but has a full interior metal skin panel to finish off the loading area. Ref: MS19, SBO0677.

The final design of boot lid for the Mk4 classic Mini; features large license plate recess as used on Mk3-on models. Heritage. Ref: BMD36001, BMD36001/HTG.

Pair of boots to fit modern replacement Italian steering racks. Ref: GSV1056, 140501/GAITER-SET, STR0068.

Rubber gasket to seal the door handle base (escutcheon) from water entry; can also be used on selected boot handles. Ref: ADA3817.

Drive shaft coupling boot as used prior to 1973 on the inner end of the drive (half) shafts. Ref: 21A963, 18G9029.

This rubber boot covers the turn signal housing inside the front fender well of the classic Mini. Ref: 576105, 37H5527, 508162.

Rubber boot to seal handbrake lever entry into backing plate. Fits both sides. Ref: 17H7612, 99268P.

Rubber boot that insulates the heavy leads to the starter solenoid. Ref: CTB920, 858266, 8G548, 8G0548.

Replacement classic Mini steering rack boot; can be easily installed with the rack in the car. Ref: BHM7113, GSV1153, QG1005, BHM7113-EA.

Pair of replacement classic Mini steering rack boots; can be easily installed with the rack in the car. Ref: BHM7113, GSV1153, QG1005.

This bracket kit will allow you to install the rod change shifter when converting from remote shift to rod change shift. All hardware and installation instructions included. INSTALLATION INSTRUCTIONS >

Genuine Heritage bracket for boot floor to the inner wheel arch. Choose right- or left-hand side.

Metal bracket normally spot-welded to the floor, and the carpet snap is then riveted to it. Ref: 14A9065.

Sheet metal bracket that is welded to the boot floor, and anchors the mounting strap for the 9 gallon fuel tank. Ref: CZH3241.

Metal bracket with captive nuts for mounting the electric fuel pump to the rear subframe. Ref: 21A750, 21A0750.

Angled sheet metal bracket that bolts to the bulkhead in the engine compartment and supports both the Mk1 hydrolastic hose and fuel line. Ref: ALA5557.

Angled sheet metal bracket that bolts to the bulkhead in the engine compartment and supports both the Mk2-Mk3 hydrolastic hose and fuel line. Ref: ALA6599.

Bracket that retains the brake line and hydrolastic pipe on wet-suspension classic Minis. Ref: 21A1522.

Refurbished bracket for Hydroelastic classic Minis only, to retain the brake line and hydroelastic pipe. Ref: 21A1522, U-21A1522, 21A1522-USED.

Thick metal bracket between the gearbox and the stabilizer rod at the left rear of some classic Mini models.

A little flash for your engine bay! A nice stainless coil bracket to replace that dull original one. Easy and inexpensive, an ideal gift item.

Metal bracket that attaches the push-button washer pump GWW102 to the lower dash rail. Ref: 14A7274.

Metal bracket attatching push-button washer pump GWW102 to the lower dash rail. Long Mk2 version that accomodates extended padded dash. Ref: 14A7274.

A very nice reproduction of the metal bracket for the Mk1 windshield washer bottle. Ref: 13H232, 37H9712.

Small bracket to mount the large number plate mount on the rear valance on the Van and Estate. Two (2) required.

Mounting bracket for Pertronix ignition coils, in a bright chrome finish. Ref: PER10002, 10002.

Mounting bracket for Pertronix ingition coils, zinc in a matte finish. Ref: PER10001, 10001.

Aftermarket bracket to fit rear inner wheel arch to floor in the classic Mini Saloon (sedan) boot. Choose right- or left-hand side.

Upright metal steady bracket for the Smiths PCV valve, as fitted to twin carb classic Minis. Ref: 12G609, 13H5191.

Brackets that bolt to the lower dash rail and locate the switch panel within ALA6621 lower dash pad. Ref: ALA6652, ALA6653.

S-shaped metal bracket at the engine end for the ''dog bone'' stabilizer rod. Ref: 21A2387.

Metal mounting bracket for ''D''-shaped Classic Mini windshield washer bottle GWW906. Ref: CZH1624.

Sheet metal mounting bracket for windshield washer bottle on classic Minis 1990-on. Ref: CZG1496.

Washer bottle bracket in the original shape as used on Mk1 classic Minis.

A modernized version of the metal bracket for the Mk1 windshield washer bottle, in stainless steel. Ref: 37H9712, 13H232.

Upgraded brake hose set for front disc brakes; Teflon-lined inner hose is protected by stainless steel braided covering. Ref: C-AJJ4026, SBR0009.

Five-piece braided stainless brake hose that includes a clutch hose for pre-Verto setups. Ref: SBR0011, C-AJJ4027.

Racing-quality Teflon-lined stainless braided hose set with banjo clutch hose as required for Verto clutch classic Minis.

Front hose kit only. Correct length for use with disc brakes; hardware included. Ref: C-AJJ4030.

Special conversion brake hose set in braided stainless material for installation of 4 piston Metro calipers on a classic Mini.

Pair of rear hoses only in racing-spec Teflon-lined braided stainless material.

Special brake hoses with a banjo bolt and fitting for the cylinder end of the hoses. Ref: C-AJJ4031B.

This repair kit will fit both the classic Mini .75'' bore clutch master cylinders and early .75'' brake master cylinders. Ref: GRK3004, 8G8430, BHM7127EVA, 52251.

Rear brake adjustment kit for drum brakes, for one wheel. Ref: 17H7620, HA100.

Sturdy U.K.-made wrench that is useful for adjusting rear brakes. Ref: BLM810, 660120, STL0011.

Screw used to force the brake shoe adjusting wedges outward to compensate for wear of the friction material over time. Ref: 17H7619.