All Products

Block letter ''Morris Cooper'' boot badge for Mk1 classic Minis. Ref: 24A24, 24A0024.

Boot lid badge for the Mk3 classic Mini 1000. Ref: CZH1357.

Boot lid badge for the Mk3 classic Mini Cooper S. Black on chrome backing.

Mk2 Morris Cooper boot badge plastic insert. Ref: ALA6537, ALA6542.

This kit contains all the boot board brackets and mounts that were fitted on original Coopers, Wolseley Hornet and Riley Elf with boot boards fitted as standard.

Boot board bracket set. For original left-hand tank, 6.6 US gallons, spare tire up to 165 size. No instructions are included, welding required.

Boot board bracket set; for original left-hand tank, 9.0 US gallons, spare tire up to 165 size.

Boot board bracket set; for original left-hand tank, 9.0 US gallons, when spare tire is up to 145 size.

Kit suitable for the fitting of boot boards for classic Minis with single fuel tanks built after 1980.

Center bracket for boot board, includes rubber catch for boot board clip 11.41.13.05 (not included). Normally this bracket is riveted into place.

If your classic Mini does not have a boot board covering the spare tire, you don't know how handy it is to have!

One of two side brackets used to support the boot board; may need replacing due to abuse or rear end accidents. Ref: 14A9781.

Boot board clip completes bracket set CK948. Mounts to bottom of boot board.

Boot board recovering carpet kit with matching vinyl edging for single-tank classic Minis to 1980.

Boot board recovering carpet kit with matching vinyl edging for single-tank classic Minis to 1980. Black.

Boot board recovering carpet kit with matching vinyl edging for twin-tank classic Minis 1962-1980

Black boot board recovering carpet kit with matching vinyl edging for twin-tank classic Minis 1962-1980. Ref: CK967, CK967A.

Carpeted boot board that, with the boot board bracket kit, will fit any Classic Mini Saloon with the single 7.5 gallon tank. Ref: CK953.

Black carpeted boot board that, with the boot board bracket kit, will fit any Mini Saloon with the single 7.5 gallon tank. Ref: CK953A.

Carpeted boot board for single-tank classic Minis to 1980

Carpeted boot board for single-tank classic Minis to 1980; black. Ref: CK951A.

Carpeted boot board for twin-tank classic Minis 1962-1980, in-stock selected colors. Ref: CK952, CLK952A.

Carpeted boot board for twin-tank classic Minis 1962-1980

Genuine Heritage boot floor complete stamping including the rear seat base; does not include battery box. Ref: ALA5513, ALA5513/HTG.

This textured, flexible PVC mat fits single-tank classic Minis, and simply lays on top of the spare tire and battery cover to give a neat, finished-looking boot area

Handy reproduction panel extends forward from the classic Mini Saloon (sedan) boot opening to cover the area most frequently affected by rust or accident damage

Repair panel for the flat section of the classic Mini boot floor adjacent to the battery box. Ref: MS24L MS24R, SBO0640, SBO0641.

This genuine British Motor Heritage body panel goes from seam to seam, and from bumper to trunk opening.

Replacement boot kit for those steering racks that have two different size of boot, 26mm and 42mm. Ref: GSV1004, SKS01, QG1050, QG1002.

Superior-quality steering rack boot set, with metal retainer straps. Ref: GRG205, GSV1153.

Originally a factory-optional accessory on the Mk1 classic Mini, this mat was unique in that it attaches to the boot lid and neatly covers the inside of the boot area, completely hiding the spare wheel and the battery. Ref: CK722A, CK722.

This simple cable, used on each side of the classic Mini Saloon (sedan) boot/trunk lid, keeps it from dropping too low when open. Ref: 14A6740.

Rubber seal that fits the later classic Mini boot/trunk handle introduced in 1972. Ref: CZH1747.

Locking boot t-handle, chrome plated, for classic Mini Mk1, Mk2, Van, and Estate (excl. Woody). Ref: 14A7194.

Classic Mini boot (trunk) handle as introduced in 1972 and used until the end of production. Ref: CZH1725, JRC2844.

Thick paper gasket for the lower section of the boot (trunk) lid hinge. Ref: 24A2176, BMP402.

Thick paper gasket for the top section of the boot lid hinge. Ref: 24A2175, BMP401.

Reproduction panel that economically replaces the original classic Mini boot hinge panel from hinge to hinge.

Pair of classic Mini boot lid hinges; mounting hardware included. Fits all years classic Mini, 1959-2000. Ref: BMB36002/3, BMB36002, BMB36003, 8B12602.

Nice reproduction classic Mini boot (trunk) lid hinges in chrome for a fresh look. Ref: 8B12601, SPD0002, BMB3600C.

Original-style metal lamp housing for boot (trunk) lids beginning with Mk3 classic Mini models. Ref: 13H6900, 13H6900P.

Boot lid seal to fit on the body instead of on the boot lid, as used 1989-on. Ref: CKE10018.

Rubber seal that mounts to the boot lid using twenty-six (26) spring clips (14A6585) that press into holes in the inner frame of the lid. Ref: 14A6584, 14A6584-MS.

Lightweight fiberglass boot lid skin (only); ready to sand and paint. For Mk1 and Mk2 classic Minis with the hinged number plate

Lightweight fiberglass boot lid skin (only), ready to sand and paint. For Mk3 and later classic Minis.

Steel outer boot lid skin only, for repairing the existing boot lids of classic Minis from 1970-on. Heritage.

Fiberboard liner in black with hardware kit to cover the open frame of the classic Mini boot lid

The classic Mini Mk1-2 boot (trunk) lid is identified by a rectangular indentation to accept the long, hinged license mounting plate. Ref: 28G110, 28G110/HTG, 28G0110.