Weatherstripping

Bonnet cloth braid to prevent metal-to-metal contact. Sold in one-meter lengths. Ref: BSE1066, SBO0265, BB01.

Push-on rubber and metal seal for MPi (multi-point injection) classic Minis.

V-section seal fits across the front of the bonnet on late classic Minis; helps prevent the bonnet from vibrating against the front panel crossmember. Ref: JRC7898, CZH1953.

Seal found at the rear of the engine bay; helps prevent the ingress of water and debris into the engine compartment. Ref: JRC7008.

Self-adhesive neoprene seal that fits in the channel of the windshield cowl. Creates a seal when the bonnet is closed.

Rubber seal that fits the later classic Mini boot/trunk handle introduced in 1972. Ref: CZH1747.

Thick paper gasket for the lower section of the boot (trunk) lid hinge. Ref: 24A2176, BMP402.

Thick paper gasket for the top section of the boot lid hinge. Ref: 24A2175, BMP401.

Boot lid seal to fit on the body instead of on the boot lid, as used 1989-on. Ref: CKE10018.

Rubber seal that mounts to the boot lid using twenty-six (26) spring clips (14A6585) that press into holes in the inner frame of the lid. Ref: 14A6584, 14A6584-MS.

Rubber gasket to seal the door handle base (escutcheon) from water entry; can also be used on selected boot handles. Ref: ADA3817.

1/2'' diameter rubber buffer used to cushion the boot board in the trunk of a classic Mini Cooper S, and also the folding rear seat on the Traveller. Sold each.

Rubber finishing plug for the tubular bumper on early classic Mini Mokes. Ref: HYK2575, HYK2675, ALA7190.

Clip to retain the rubber seal on the classic Mini boot lid (to 1989) or the rear doors of the classic Mini Traveller and Van. Ref: 14A6585, 14A6585KIT.

Clip to attach inner guide found on all classic Mini roll-up window doors. Ref: EYC10048, AAU8399.

Rubber seal for door check after 1986; choose right- or left-hand side.

Specially-shaped seal keeps water out of the check arm opening. Left-hand side. Ref: CZH4053.

Specially-shaped seal keeps water out of the door check arm opening; right-hand side. Ref: CZH4052.

Small gasket for leading end of exterior door handle of roll-up window cars. Ref: CZH1729, ALA5795.

Gasket between rear of door handle and exterior door skin. Ref: ALA5795.

Black solid rubber u-channel door seal, with hollow foam seal section, as origial for early classic Minis. Ref: XGA9934.

Black rubber, bulb-type seal to fit the small door gap of classic Mini sliding-window doors. Ref: XGA9934, XGA9934V.

Modern bulb seal design with vinyl-covered u-channel to fit the door opening flange on all internal-hinge classic Minis. Ref: CGA2835, CGA2835MS, CFB10047.

Improved original rigid-type Mk1-2 classic Mini window channel, with reinforced internal wire and holes in for drainage and securing. Ref: 24A88, 24A88_original.

Molded rubber seal that fits inside the chrome window pull on the rear side windows on the classic Mini Estate. Ref: 14A7637.

Foam gasket to fit tail lamp lenses with integral clear reverse lenses, except for Altissimo-made units. Fits both left and right sides. Ref: XFH100460.

Foam rubber lens seating gasket as used on Mk2 tail lamp. Ref: 37H6778.

The Mk1 tail lamps use this sponge rubber gasket between the lamp base and the body. Ref: 54571330, 57H5399, 47H5361.

The classic Mini Van, Estate (Wagon) and Traveller (Woody) tail lamps use this sponge rubber gasket between the lamp base and the body. Ref: 57H5167.

This sponge rubber gasket fits between the lens and the tail lamp assembly on the Mk1 classic Mini. Ref: 54570450, 57H5399.

Large rubber grommet to fit 1'' hole for passage of wires, hoses, pipes etc. The center hole is 7/32''. Ref: 5L23, 5L0023.

General-purpose PVC chassis grommet; 5/16'' outer diameter. Ref: GMT522.

Rubber grommet in boot (trunk) lid to isolate the wires to the license plate lamp. Ref: 3F90, 3F0090.

Rubber grommet to prevent chafe of the tank vent hose where it passes through the boot floor. Ref: RFN403, RFN0403.

Rubber grommet to fit in the bottom of GWW935 washer bottle, and to be used with GWW1192 pump. Ref: BAU2043A.

This thick gasket is treated to prevent water damage. Fits the long section of the hinge on the door. Ref: ALA7844, BMP134, 24A2174.

Specially treated thick gasket to resist water damage. Fits the small part of the door hinge on the hinge panel. Ref: BMP135.

Special thick fiber gasket to seat the door hinges to the body on classic Mini Van and Estate rear doors. Ref: 14A8434, ALA8465.

32'' chrome and rubber inner door window scraper/seal for roll-up window classic Minis; fits either side. Ref: EJU10003, CZH3576, JPC8153.

Rubber seating gasket for under the metal license plate lamp housing as used on Mk3 and later classic Minis. Ref: 13H6010, 54571498.

Nylon insert snaps into the square holes around the headlight bucket on original fenders; the headlight bucket retaining screws then thread into the insert. Ref: GHF1030, 13H226, 13H0226.

Outer scraper seal/trim introduced in 1981 and generally used to retrofit to earlier Mk3-on cars in lieu of the original version, which did not have rubber safety tips. Ref: PAM1014, PAM1015.

Original-design outer door scraper seal/trim, with no rubber safety tips on the ends. Ref: CZH1666, CZH1667.

OE-style 20mm rubber plug, fits 13/16'' holes. Ref: 14A7090, 14A7090A, 14A7090L.

Rubber plug, 7/8'' diameter. Fits radius arm cover on Mk1 and Mk2, and wiper hole on cowl of later classic Minis. Ref: 14A7091, 14A7091E.

Rubber plug to fit the 21A1470 locktab for the two-bolt front subframes; used on dry suspension classic Minis 1959-1976. Ref: RFR220, RFR0220.

1'' floor plug; fits classic Mini front floor plus the rear seat pan. Ref: 14A7081, C548.

Genuine Rover front floor and rear seat tray plug; fits 1'' hole. Ref: 14A7081.