Plugs, Grommets & Gaskets

Thick paper gasket for the lower section of the boot (trunk) lid hinge. Ref: 24A2176, BMP402.

Thick paper gasket for the top section of the boot lid hinge. Ref: 24A2175, BMP401.

Rubber gasket to seal the door handle base (escutcheon) from water entry; can also be used on selected boot handles. Ref: ADA3817.

1/2'' diameter rubber buffer used to cushion the boot board in the trunk of a classic Mini Cooper S, and also the folding rear seat on the Traveller. Sold each.

Rubber finishing plug for the tubular bumper on early classic Mini Mokes. Ref: HYK2575, HYK2675, ALA7190.

Small gasket for leading end of exterior door handle of roll-up window cars. Ref: CZH1729, ALA5795.

Gasket between rear of door handle and exterior door skin. Ref: ALA5795.

Foam gasket to fit tail lamp lenses with integral clear reverse lenses, except for Altissimo-made units. Fits both left and right sides. Ref: XFH100460.

Foam rubber lens seating gasket as used on Mk2 tail lamp. Ref: 37H6778.

The Mk1 tail lamps use this sponge rubber gasket between the lamp base and the body. Ref: 54571330, 57H5399, 47H5361.

The classic Mini Van, Estate (Wagon) and Traveller (Woody) tail lamps use this sponge rubber gasket between the lamp base and the body. Ref: 57H5167.

This sponge rubber gasket fits between the lens and the tail lamp assembly on the Mk1 classic Mini. Ref: 54570450, 57H5399.

Large rubber grommet to fit 1'' hole for passage of wires, hoses, pipes etc. The center hole is 7/32''. Ref: 5L23, 5L0023.

General-purpose PVC chassis grommet; 5/16'' outer diameter. Ref: GMT522.

Rubber grommet in boot (trunk) lid to isolate the wires to the license plate lamp. Ref: 3F90, 3F0090.

Rubber grommet to prevent chafe of the tank vent hose where it passes through the boot floor. Ref: RFN403, RFN0403.

Rubber grommet to fit in the bottom of GWW935 washer bottle, and to be used with GWW1192 pump. Ref: BAU2043A.

This thick gasket is treated to prevent water damage. Fits the long section of the hinge on the door. Ref: ALA7844, BMP134, 24A2174.

Specially treated thick gasket to resist water damage. Fits the small part of the door hinge on the hinge panel. Ref: BMP135.

Special thick fiber gasket to seat the door hinges to the body on classic Mini Van and Estate rear doors. Ref: 14A8434, ALA8465.

Rubber seating gasket for under the metal license plate lamp housing as used on Mk3 and later classic Minis. Ref: 13H6010, 54571498.

Nylon insert snaps into the square holes around the headlight bucket on original fenders; the headlight bucket retaining screws then thread into the insert. Ref: GHF1030, 13H226, 13H0226.

OE-style 20mm rubber plug, fits 13/16'' holes. Ref: 14A7090, 14A7090A, 14A7090L.

Rubber plug, 7/8'' diameter. Fits radius arm cover on Mk1 and Mk2, and wiper hole on cowl of later classic Minis. Ref: 14A7091, 14A7091E.

Rubber plug to fit the 21A1470 locktab for the two-bolt front subframes; used on dry suspension classic Minis 1959-1976. Ref: RFR220, RFR0220.

1'' floor plug; fits classic Mini front floor plus the rear seat pan. Ref: 14A7081, C548.

Genuine Rover front floor and rear seat tray plug; fits 1'' hole. Ref: 14A7081.

Aftermarket floor plug 3/4''. Fits rear floor and battery box. Ref: 14A7090, C546, 14A7090E.

Thick, heavy rubber plug as used originally on classic Minis with 7/8'' holes in the floors, Mk1-Mk2 radius arm cover plates, unused steering column hole, antenna holes, and unused wiper holes in the cowl.

Flat rubber plug for 9/16'' hole. Sold each.

Rubber plug to fit the 5/16'' hole on each inner fender and the rear seat pocket on Mk1 classic Minis. Ref: 2H7274.

Small rubber plug to block unused holes in the rear valance body panel where lights are not fitted. Ref: 14A7032.

Large rubber plug on left rear of the classic Mini remote housing that allows access to the shift rod and socket.

Small rubber seating gasket under the door handle safety boss. Ref: 24A1835.

Thick rubber seal between the front turn signal and the body, as used on U.K. classic Mini Mokes. Ref: 54573115.

Foam rubber seal that goes between the headlight bucket and the fender on MPi classic Minis equipped with motorized self-adjusting headlights. Ref: XBC105250.

Thick rubber seal, fitted under the glass lens on the license plate light used on Mk1/Mk2 classic Minis, plus Van, Estate, and early Moke. Ref: 54571498, 57H5368.

Rubber seal between lamp base and body on Mk2 classic Mini Saloons. Ref: 37H2689, 37H2690.

Left-hand side rubber gasket for lamp base-to-body on Mk4 and later classic Mini Saloons with reverse lights. Ref: 37H2691, 54590554.

Right-hand side rubber gasket for lamp base-to-body on Mk4 and later classic Mini Saloons with reverse lights. Ref: 37H2692, 54590555.

Flanged rubber grommet that fits around the fuel tank neck to seal the hole and to prevent vibration. Ref: 14A7057, 14A7057E.

Rubber grommet fits around the tank neck to seal the hole and to prevent vibration. Original-type as used pre-1997. Ref: 14A7057, 14A7057GENUINE.

Thin, flat rubber tank neck grommet, designed for use with the revised tank neck of the MPi classic Mini. Ref: WGG100010.