Products 49-96 of 113
Show
Item #: GHK1140 -
Superior-quality genuine Timken front taper-roller bearing set. Ref: GHK1140, BKS29.
Price: $73.50
View
7/17/2019 2:00:00 AM
54.9500
Pending Warehouse Check
Item #: FOR131 -
This new spacer had been made from a harder material than standard, and increases wheel bearing stablity and life.
Item #: 13H107 -
Original-style front wheel bearing, 30mm ID, as used on 1959-1962 classic Minis
Item #: 2A4362 -
OE-spec lower arm fulcrum pin. Ref: 2A4362, 21A1889.
Item #: 2A4362E -
Any time the front end of the classic Mini is ''kerbed'' or takes a hard impact, this pin should be checked. Ref: 2A4362, 2A4362MS, 2A4362E.
Item #: UHN0400 -
This fitting is used in several places, including front swivel hubs and outer end of rear radius arm shaft. Ref: UHN400, LN10051, UHN0400.
Item #: UHN0445 -
Angled grease nipple for lubing the front upper arm. Ref: UHN445, UHN0445.
Price: $99.95
View
9/10/2020 2:00:00 AM
89.95
Pending Warehouse Check
Item #: SSS0015K -
Genuine U.K.-made Hi-Los are adjustable length struts that allow the classic Mini to be lowered or raised in each corner to achieve different ride height and corner weights. Ref: HILO, HI-LO, SSS0015K.
Item #: KAD011 -
EN16T steel adjustable front tie rods, made by KAD. Ref: KAD011, KAD1012265, 1012265/L, 1012265.
Price: $7.50
View
11/8/2017 2:00:00 AM
9.9500
Pending Warehouse Check
Item #: GSV1118E -
Knuckle joint that transmits movement of the suspension arms into the springs. Ref: GSV1118, GSV1118MS, 21A1163, QSJ177S.
Price: $5.95
View
4/8/2019 12:00:00 AM
Pending Warehouse Check
Item #: 21A0425HD -
Flexible polyurethane knuckle joint boot for the classic Mini, more resistant to tearing, oxidation and ozone than the standard rubber boot. Ref: 21A425EVO, 21A425, 21A425HD.
Item #: 21A0425 -
Rubber boot to protect the metal pin in the knuckle joint from grit and eventual damage. Ref: 21A425, 21A0425.
Item #: 21A0423 -
This cup isolates the knuckle pin from the suspension arm and must be in good shape to do its job properly.
Item #: 21A0423-OE -
Rover-supplied version of the nylon cup for the suspension knuckle joint assembly. Correct shape, flat at the tip for correct fit.
Price: $52.50
View
12/18/2020 12:00:00 AM
59.9500
Pending Warehouse Check
Item #: GSV1264 -
Knuckle joint with built-in spacer, as used on the front of classic Minis equipped with 13'' wheels to raise the suspension for clearance.
Price: $12.95
View
12/22/2020 2:00:00 AM
Pending Warehouse Check
Item #: GSV1118EVO -
High-spec material knuckle joint assembly for front or rear of the classic Mini. Ref: GSV1118EVO, GSV1118.
Price: $11.50
View
12/23/2020 12:00:00 AM
10.0000
Pending Warehouse Check
Item #: SSS0026 -
Replacement knuckle joint assembly to fit the Smootharide aftermarket suspension kit. Shaft diameter is 14mm.
Item #: SSS0168 -
On-car adjustable lower suspension arms that use standard or poly bushings. Ref: C-AJJ3360, SSS0168, SPDSP431A.
Item #: SSS0166 -
On-car adjustable lower suspension arm with Heim (Rose) joint. Includes spacers for above and below heim joint. Ref: C-AJJ3360A, SSS0166, SPD34.
Item #: C-AJJ3364 -
1.5-degree negative camber front suspension arms; sold per pair. Ref: C-AJJ3364.
Price: $94.50
View
5/22/2019 2:00:00 AM
89.9500
Pending Warehouse Check
Item #: 21A1879/81 -
Lower control arms for Mk2-on classic Minis, featuring revised inner eye to accept the improved metal-sleeved inner bushing. Ref: 21A1879, 21A1881.
Price: $23.50
View
11/28/2018 12:00:00 AM
19.9500
Pending Warehouse Check
Item #: GSJ0268 -
Ball joint as used on early Metro swivel hubs, which will fit the standard-sized tapered hole in classic Mini suspension arms. Ref: GSJ268, QSJ1059S, NAM4376EVA.
Price: $43.95
View
7/22/2019 12:00:00 AM
37.9500
Pending Warehouse Check
Item #: C-STR640A -
Set of four (4) top subframe tower mounts for road-use classic Minis 1976-2000. Ref: C-STR640A, C-STR640.
Item #: 21A0079 -
The smaller of the two nuts used in the center of the classic Mini's front wheel; measures 1.125'' across the flats of the nut.
Item #: BTA249E -
This large 1-5/16'' nut fits only the larger CV joint used in classic Mini Cooper S and later 8.4'' brakes. Uses 34mm socket size. Ref: BTA249E, BTA0249.
Item #: BTA249 -
This castle nut fits only the larger CV joint used in Cooper S and later 8.4'' brake-equipped classic Minis. Ref: BTA249, BTA249MS.
Item #: FNZ0508 -
Locking nylon-insert nuts to replace nuts on front upper control arms and rear radius arm pivot pins. Ref: FNZ508, FNZ0508.
Item #: GHF0223 -
3/8-24 nylon nut, as used on shock absorbers, 2A4362 fulcrum pin. Ref: GHF223, GHF0223.
Item #: GHF0224 -
Nylock nut for diagonal tie rod from lower suspension arm to front of subframe. Ref: GHF224, GHF0224, HDWN2713.
Item #: 2A7327 -
This seal is used in both front and rear suspension. Use four (4) in front and four (4) in back. Ref: 2A7327.
Item #: 13H2776 -
Single screw to attach the rebound buffer to the subframe. Ref: 13H2776.
Price: $33.95
View
MADEINUSATAG||
Pending Warehouse Check
Item #: FOR035 -
This oversized, tall rebound buffer is recommended for classic MInis that have been severely lowered, or any classic Mini converting to coil springs.
Item #: 2A4267E -
Reproduction rebound buffer, mounts on the subframe to stop downward movement of the upper arm. Ref: 2A4267, 2A4267E.
Item #: FAM3968E -
Reproduction rubber cone/spring for use on dry-suspension classic Minis. Fits front or rear. Ref: FAM3968, FAM3968E.
Price: $146.95
View
11/16/2017 12:00:00 AM
149.9500
Pending Warehouse Check
Item #: C-STR688 -
Competition-quality rubber suspension springs with a special shape and material. Ref: C-STR688.
Item #: C-STR0687 -
Uprated rubber cone spring that will stiffen up the suspension while lowering it at the same time. Fits front or rear. Ref: C-STR687.
Item #: HDWS288 -
Short Pozidrive head screw used to retain the front drum and standard rear drum to the drive flange or rear hub. Ref: CMZ407, HDWS288, DS1X100.
Item #: HDWS293 -
Pozidrive (not Phillips) head screw to fasten the flange to the classic Mini Cooper S brake disk. Ref: SF604061, HDWS293.
Item #: SF604051 -
Small Pozidrive head screw as used in drive flange and brake drum applications. 0.51'' thread length. Ref: SF604051.
Price: $9.50
View
10/21/2019 2:00:00 AM
8.9500
Pending Warehouse Check
Item #: 2A4295 -
Metal seal collar sits just inside the drive flange on front drum brakes, 997 and 998 Cooper discs only. Ref: 2A4295.
Item #: GHS0173 -
Two-piece seal includes a separate water ring to deflect the force of splashing water. Ref: GHS173, GHS0173.
Item #: GHS0101 -
Outer wheel bearing grease seal on the front swivel hub of both drum and disc brake models. Ref: GHS101, BTA9014.
Price: $5.50
View
5/6/2021 2:00:00 AM
6.0000
Pending Warehouse Check
Item #: 2A7323 -
Thick washer found under the 1.125'' outer CV nut on all small CV joint models. This includes all drum brake and 997/8 Cooper models.
Item #: C-STN236/7 -
GAZ premium gas-filled performance shocks, for cars lowered 2'' or more from standard. Ref: C-STN236, C-STN237.
Item #: C-STN231/3 -
GAZ premium gas-filled performance rear shock, for standard-height vehicles; choose front or rear. Ref: C-STN231, C-STN233.
Item #: KYB-Gas -
Pressurized KYB self-adjusting slimline shock absorbers for standard ride-height road classic Minis. Ref: 552018, 552019, GSA388A, GSA389A.
Item #: KYB -
Affordable, quality shocks to reduce your classic Mini maintenance budget; an ideal upgrade for road cars! Ref: 442001, 442002, GSA71541, GSA71542, GSA388-KYB, GSA389-KYB.
Price: $41.95
View
11/13/2018 12:00:00 AM
39.9500
Pending Warehouse Check
Item #: C-STR642 -
Solid brackets for the rear of the front subframe of post-1976 classic Minis. Ref: C-STR642.
Questions? Email parts@7ent.com, or call
(800) 992-7007 (U.S. only) or (530) 886-0771