Fuel System

Replacement points for the set under the plastic cap of OEM SU electric fuel pumps. Ref: AUB6106, AUB6106A, XFP5910.

An extended left-hand drive plastic gauge pod with 80mm tachometer hole, and a special inner metal plate that holds the gauges securely

An extended right-hand drive plastic gauge pod with 80mm tachometer hole, and a special inner metal plate that holds the gauges securely.

Replacement rubber end collar for braided Petroflex-style fuel hose; inside diameter 1/2''. Ref: GGT100.

Rubber seal for the clip-in sending unit, used on all classic Mini Saloon (sedan) fuel tanks after the screw-in type was discontinued. Ref: ARA1502.

Small screw used to retain the fuel sending unit in in Mk1 Mini up to 1964, Van, Estate, and Pickups with underfloor fuel tank. Sold each, six (6) required.

Rubber seal at the top of the cast metal elbow(s) as fitted to many early classic Mini 850 and Cooper models. Ref: 12A1433.

O-ring seal used when replacing fuel filters on SPi (single-point) or early MPi (multi-point injection) classic Minis. Ref: EDP9976.

Heavy rubber seal that goes on top of the gas tank on fuel-injected classic Minis, and seals the fuel pump mounting flange to the tank. Ref: EDP9317.

Special thick poly washer replaced the original one for gas cap installation in order to prevent leakage when the old washer has deteriorated. Ref: 21A2109.

Rubber seal found under the plastic banjos on all SU electric and electronic fuel pumps. Ref: AUB676, AUB0676.

Mounting kit for 45DCOE or 40DCOE side draft Weber carbs. Ref: 99005.145, SMW40/45.

Phenolic spacer for HIF6/HIF44 1.75'' carb. Approximately .50'' thick. Ref: 12B561, GUG705602GM, 12B0561B.

Spacer needed when a new mechanical fuel pump is fitted; approximately 0.520'' thick. Ref: AUB5040, 12G4520, GUG705603GM.

Speedometer for center binnacle application, typically through 1983; late classic Mini Cooper S-style gauge with markings up to 130mph. Ref: 13H4442, 13H4442MG.

Cooper S speedometer with the kilometer scale as primary. Includes fuel gauge, voltage stabilizer and indicator warning lamp lenses. Ref: 13H4444, 13H4444MG.

Spring for idle adjust screw on SU HS carburetors.

One-meter lengths of braided fuel hose. Rubber hose with braided stainless steel outer cover; cut to length Ref: GGT1001M, GGT1005M.

10'' long stainless steel braid covered rubber fuel hose, similar to the type commonly found on most British cars. Ref: GGT104, PPK4.

11.5'' long stainless steel braid covered rubber fuel hose, similar to the type commonly found on most British cars

14'' long stainless steel braid covered rubber fuel hose, similar to the type commonly found on most British cars

2.5'' long stainless steel braid covered rubber fuel hose, similar to the type commonly found on most British cars

22'' stainless steel braid covered rubber fuel hose, similar to the type commonly found on most British cars. Ref: GGT107, PPK7, GGT0107.

5'' long stainless steel braid covered rubber fuel hose, similar to the type commonly found on most British cars. Ref: PPK2, GGT108, GGT0108.

7.5'' long stainless steel braid covered rubber fuel hose, similar to the type commonly found on most British cars

Aluminum cast stub stack for SU HS4 and HIF4/38 carburetors. Ref: SS51, SIE0313.

This is the proper stud to use in the aluminum intake manifold for twn HS2 carbs. 3/8'', fine thread on one end, course on the other. Can also be use as the stud for spin-on filter housing.

Float extension kit for vintage race Classic Minis using period-correct SU H4 carburetors.

For vintage race Minis using period-correct SU H4 carburetors; these float bowl extensions with floats help to eliminate fuel surge on the track.

A very handy kit of special HIF carburetor screws, springs, and pivot pin. Ref: SIE0078, CSK004.

Replacement brass tank neck adapter to allow the Aston flip-cap to screw on to a standard classic Mini 2.5'' tank neck. Ref: COL25, SIE0088.

Flanged rubber grommet that fits around the fuel tank neck to seal the hole and to prevent vibration. Ref: 14A7057, 14A7057E.

Rubber grommet fits around the tank neck to seal the hole and to prevent vibration. Original-type as used pre-1997. Ref: 14A7057, 14A7057GENUINE.

Thin, flat rubber tank neck grommet, designed for use with the revised tank neck of the MPi classic Mini. Ref: WGG100010.

Durable metal replacement for the original plastic 48mm classic Mini multi-point injection (MPi) throttle body. Ref: ABF622.

Offset throttle cable guide as used on twin carbs, but adaptable for most installations. Ref: AEG349, 12A259, AEG0349.

54'' throttle cable for the later 1995 and 1996 fuel-injected SPi classic Mini. Includes cable and outer sheath assembly.

Heavy-duty cable with a little extra length at 31''; useful for custom applications and Weber carb conversions. Ref: C-AHT85, C-AHT0085.

The throttle cable needed for left-hand drive classic Minis with HIF carb. 22'' outer sheath. Ref: SBB10126.

The throttle cable needed for right-hand drive classic Minis with HIF carb. Ref: SBB10099.

Throttle cable with threaded end for left-hand drive 1997-on MPi classic Minis. 38'' length.

Throttle cable for right-hand drive MPi classic Minis; aftermarket.

Throttle cable for left-hand drive SPi classic Mini models. Approximate length 54''.

Throttle cable for right-hand drive SPi classic Minis.

Anti-friction throttle cable with heavy-duty lined outer cable; fits most early classic Minis with single or dual carbs. Ref: NAM7914, AHA5746.

Throttle disc kit without poppet valve for SU HIF44 carburetor. Includes disc, retaining screws and carb mounting gaskets.

Genuine S.U. throttle disc kit for HS2 carburetor; includes disc, hardware, and mounting gaskets. Ref: WZX1320.

Solid throttle disc without the popper valve, for SU HS4 carburetor. Ref: WZX1323, 111-6058.