Body & Trim

Kit contains the parts to install the overriders to the bumper and the trim bars to the overriders; includes fasteners, spacers, bumper plates, and rubber overrider seating strip.

Rubber finishing plug for the tubular bumper on early classic Mini Mokes. Ref: HYK2575, HYK2675, ALA7190.

Black reproduction bumper, as used on some Special Edition classic Minis. Ref: CZH4341MS, CZH4341.

Reproduction chrome bumpers of the originals found on Mk1 and Mk2 classic Minis. Ref: 14A6779, 14A6779MS.

Front bumper bar assembly for British-made, 10” wheel Moke.

Rear bumper bar assembly for British-made, 10” wheel Moke.

Faithful Heritage reproduction of the small quarter bumper for the classic Mini Van, Estate, and Pickup. Ref: 14A7550, 14A7550S, 14A7550/HTG.

Reproduction of the classic Mini's bumper in stainless steel, with the original-type open ends. Ref: DPB10165, DPB10165MS, DPB10165E.

Stainless steel bumper, made to Rover's 1996-on spec; features rolled edges for safety. Ref: DPB10166, DPB10166-OE.

Replacement bumper for early classic Minis with the Deluxe or Cooper bumpers with overriders and trim bars. Ref: 14A9871.

Ribbed flat one-piece cargo bed floor for classic Mini Pickup and Van models.

Phone holder with 5v USB port replaces the existing ashtray in the Classic Mini padded dash rail. Ref: MSA4000.

This is the full-width chrome finisher strip that clips to the lower dash tray edge. Ref: 14A8009.

Clevis pin used in conjunction with door check arm ADA5671, on all classic Minis with roll-up windows from 1970 to 2000. Ref: CLZ412, CLZ0412.

Small plastic socket clip for pins on the reverse side of body badges. Ref: GFK7514, GHF1531.

Clip to retain the rubber seal on the classic Mini boot lid (to 1989) or the rear doors of the classic Mini Traveller and Van. Ref: 14A6585, 14A6585KIT.

This bendable metal tab is spot-welded to the underside of the floor to locate the brake and fuel lines. Ref: 11.31.06.05, ALA5536.

Clip under front floor to secure fuel and brake lines, used from 1959-1990. Weld in place beside floor pan footwell and tunnel; use two (2) per car.

Clip that attaches the chrome finisher strip (14A8009) to the lower dash tray edge.

Small e-clip to connect the door opening remote control rod plus the lock control mechanism on roll-up window doors.

Clip retains Mk3 window scraper and also door pocket trim. Ref: ADH3809.

Clip for Mk1 Austin Mini bonnet badge 24A71. Ref: PFR108, PFR0108.

Clip to attach inner guide found on all classic Mini roll-up window doors. Ref: EYC10048, AAU8399.

Black-oxide clip commonly used for the external body seam covers and the roll-up window door inner felt seals. Ref: GHF1560, GFK7515.

Anti-rust stainless steel version of the classic Mini seam cover clip. Ref: BMP128, BMP0128, GFK7515, GHF1560, BMP128MS.

1964 and 1965 Minis had an improved sun visor that could pivot around to shade from the side as well as the front. This clip was used to support the outer end of that visor. Ref: TRM129, GFK7344.

Smiths clock in 52mm size with chrome bezel; choose black or magnolia face. Ref: SIB110, SIB110MG, CA1100-01C, CA110001C.

Sheet metal panel at the bottom of the rear seat companion box. This makes a continuation of the of the inner sill. Ref: 14A8994, 14A8995.

Metal commission plate mounted on the ''slam panel'', usually on cars imported into the U.K. from other markets.

Complete rear seat side bin to fit 1990-on classic Minis. Heritage, choose right- or left-hand side

Outer skin of rear seat side bin to fit Mk1 and Mk2 Saloons. Ash-tray panel and inner stiffener not included. Ref: 14A6494, 14A6495.

Complete rear seat side bin to fit classic Mini Mk3-on models; choose right or left side. Ref: ALA5672, ALA5673.

Complete floor assembly for Mk2 Mini Estate Wagon. Will also work for Mk1 if converting to remote shift. Includes inner and outer sills, seat crossmember, rear subframe heelboard mounting panel.

Floor panel with the 1996-on revised shape footwells and a gusset section down the left side to carry the fuel-injection lines on late classic Minis (up to 2000). Ref: CZH2669, CZH2669/HTG.

Metal panel that covers the side storage panels on the classic Mini Moke. Ref: ALA7164.

Genuine Heritage jacking point with a reinforcement repair part to attach to the crossmember extension for all classic Minis. Ref: 14A8374, 14A8375.

Spring-loaded cup on the classic Mini bonnet latch pin. Ref: ADA458, ADA0458.

Spring-loaded cup on the classic Mini Clubman bonnet latch pin. Ref: 4G3676.

Minis from Mk2-on use this padded lower dash rail, which moves the switches closer to the driver's reach, and prevents barking your shins against the dash. Ref: ALA6621.

Mk3-on weld-in lower parcel shelf metal panel with hole for switch panel; fits between the A posts. Ref: BMP201.

Steel upper dash rail with center hole for ash tray. Has holes near the end to accept the padded upper dash, as used from 1984. Ref: 14A6675.

A roll of vinyl with sufficient material to do upper and lower dash rails and A-posts as was used originally on Deluxe and Cooper models of the Mini.

Black roll of leather-look vinyl with sufficient material to do upper and lower dash rails and A-posts as was used originally on Deluxe and Cooper models of the classic Mini.

Under-dash tray liner support panel for classic Minis 1970-on. Ref: DT3076, newton commercial.

Dash liner made from heavy-duty PVC with a felt backing; as commonly found on the classic Mini Van and Pickup

Liner fits in the dash tray, and is held in place by the speedo panels. Made of vinyl to match the interior trim color, and has a foam backing as original

Pair of speedometer trim panels to fit classic Mk1 Minis with the three instrument speedo binnacle set into the dash

Pair of dashboard trim panels that fit on either side of the speedometer. For 1962-1970 classic Minis fitted with the round binnacle with only the speedometer in the center of the dash.