Panels / Sheet Metal

Weld-in repair panel for the lower portion rust-prone wheel arch area; pre-shaped to the contour of the inner fender. Choose right- or left-hand side.

Rear lower side side panel for external-hinge classic Mini Van and Estate Wagon. Complete from the belt line to the lower pinch weld. Choose right (with fuel filler opening) or left side.

Plate used to blank off the Mk2-on rectangular tail lamp hole so a Mk1 lamp can be mounted in its place. Ref: MS026L, MS026R, 13H222.

This bolt-on access panel for the classic Mini Moke had to be made removable so that the fuel tank could be installed. Ref: ALA7322.

A pair of half-floor panels suitable for the classic Mini Moke; complete front to rear. Ref: ALA7076.

The weld-on panels that form the bottom of the classic Mini Moke’s side pontoon boxes, and complete the floor. Ref: ALA7318.

Main mounting bracket for the handbrake lever assembly, welded onto the back of the seat crossmember and to the rear floor section. For rod change cars with late-type single cable handbrake only.

Support bracket on floor of boot for left-hand gas tank; fits classic Mini saloons (sedans) 1959-1976. Ref: 14A6867, 14A6867/HTG.

Main mounting bracket for the handbrake lever assembly, welded onto the back of the seat crossmember and to the rear floor section. For pre-rod change cars with twin cable handbrake only.

Steel support structure for the steering rack. Spot welds to the underside of the toe board.

Outer hinge panel for MK1 and Mk2 classic Minis; reproduction. Ref: MS8R, MS8L, 14A6902, 14A6901.

For all classic Minis with external hinges, these genuine Heritage outer hinge panels fit the best. Ref: 14A6901, 14A6902, 14A6901/HTG, 14A6902/HTG.

Reproduction hinge panel for roll-up window classic Minis; fits well and is an economical solution when the budget does not permit genuine Rover panels. Ref: ALA5660, ALA5660MS, ALA5661, ALA5661MS.

Outer hinge panel for Mk3-on Minis with concealed hinges; made by British Motor Heritage. Ref: ALA5660, ALA5661.

Outer sill panels, as used in the first Austin Seven and Morris Mini Minors 1959-1960; reproduction.

Long-wheelbase classic Mini Van, Estate, and Pickup outer rocker (sill) panel, with 6 vents as used after about 1970, in standard width. Ref: MS60L, MS60R.

Extra-wide Mk1/Mk2 classic Mini Saloon (sedan) sill panels to replace or to be fitted over the original 4-vent sill panel. Ref: MS29R, MS29L.

Sills closest to the original BMC panel in terms of the shape of the vents and the jacking point reinforcement. Ref: MS30R, MS30L.

Budget replacement 6-vent sill for all Mk3-on classic Mini Saloons (sedans). Ref: MS63R, MS63L, 14A9534, 14A9535.

Classic Mini Saloon (sedan) outer sill (rocker) panel in original dimensions, as used on all classic Minis with six (6) vents after about 1970. Ref: 14A9534, 14A9535, 14A9534/HTG, 14A9535/HTG.

Extra-wide replacement classic Mini Saloon (sedan) sill panels to replace or to be fitted over the original 6-vent sill panels. Ref: MS55R, MS55L, BHM0003E, BHM0004E.

Outer sill (rocker) panel in stock dimensions for all long wheelbase Minis with four (4) vents as original from 1959 to about 1970. Ref: MS49R, MS49L, 14A9026E, 14A9027E.

Reproduction sill (rocker) panel for the classic Mini Van/Estate/Pickup, much wider than the original sill to replace the sill and into the floor. Ref: MS58R, MS58L, SBO0687, SBO0688.

Outer sill (rocker) panel in original dimensions for all long-wheelbase classic Mini variants; genuine Heritage. Ref: 14A9026, 14A9027, 14A9026/HTG, 14A9027/HTG.

Inner reinforcement of the classic Mini Moke's outside lower sill, often rusted and replaced when replacing outer sides and floor. Ref: ALA7312, ALA7313.

Rear corner repair panel for all classic Mini Pickups. Includes threaded inserts for the tailgate stay. Ref: 41.14.01.01, 41.14.01.02.

Plastic cover that finishes off the metal lever on the 1976-on bonnet latch, and also the seat adjusting latch on all years of classic Mini. Ref: CZK8289.

Closing plate for right hand rear wheel arch to the heel board; genuine Heritage. Ref: 14A6611, 14A6612, 14A6611/HTG, 14A6612/HTG.

Lower rear door inner-outer repair panel, for classic Mini Van/Estate. Aftermarket; choose right- or left-hand side.

Full-length rear floor repair for long-wheelbase classic Mini models. Ref: MS26RVAN, MS26LVAN, SBO0137, SBO0138, MS26RVAN, MS26LVAN.

Rear floor repair, left-hand side, for the classic Mini Van/Estate/Pickup. Extends 38'' from heelboard to center of seat crossmember.

Good-quality aftermarket replacements for the classic Mini Saloon (sedan) inner fender well. Choose right- or left-hand side.

This is for the area below the tail lamps from side seam to boot opening. Reproduction; choose right- or left-hand side.

This Heritage rear repair panel replaces the sheet metal from the bottom of the rear window opening down to the bumper lip, and from seam cover to seam cover.

If you have had major rear panel damage and plan to retrofit the Mk1 tail lamp look to your classic Mini, this panel fills the bill.

Entire rear section, from roof to bumper valance, with Mk2 lamp holes, boot lid, and backlight holes to fit al models from 1967 to 2000.

Rear parcel shelf panel with cut-outs (2 large and 2 small), as used for Rover-fitted speakers on late-production classic Minis

Rear quarter body panel for classic Minis with sliding-window doors. Reproduction; choose right- or left-hand side.

Rear seat back/bulkhead as fitted to early classic Minis. The large hole is for the Rotodip pole that suspended the Mini body shell on the assembly line for primer coating.

Rear seat pocket lower repair section for Mk1-2 classic Mini Saloon (sedan). Replaces rusty area where pocket contacts the floor; flanged at the top for welding.

Rear step panel with bumper mount lip, for van/estate model classic Minis. Aftermarket.

An improved rear step panel with the curved ends now included for more accurate and comprehensive repair of classic Mini Pickup bed lip and bumper flange.

Rear subframe mounting and rear floor skirt panel for all classic Mini Vans and Pickups. Ref: MS51VAN.

This economical valance stiffener panel is an excellent choice for most installations. Ref: SBO0638, SBO0639, MS40R, MS40L.

The panel you should use to provide the necessary reinforcement of the rearmost subframe trunnion block and for full closing as original of the valence panel ends. Reproduction; choose right- or left-hand side.

The classic Mini, Estate, Pickup and Van have a three-piece rear valance; these go from rear wheel to the bumper. Ref: MS52R, MS52L.

The genuine Heritage valance panel is the best-made and best-fitting, with holes and fittings as used on later classic Minis for rear fog lights, etc. Ref: 14A5497, CZH3353, 14A5497/HTG.

Center valance panel for the long-wheelbase classic Mini Van, Estate, and Pickup. Ref: MS23, SBO0015.