Exterior Trim & Fender Flares

This pair of rubber hooks can be used as quick release fasteners on almost anything; most often used on the classic Mini to secure tilt front-ends or removable bonnets

Lightweight rubber hooks most commonly used to secure fiberglass boot lid or bonnet on the classic Mini. Ref: MS119, SAC0035.

Locking boot t-handle, chrome plated, for classic Mini Mk1, Mk2, Van, and Estate (excl. Woody). Ref: 14A7194.

Anti-rust stainless steel version of the classic Mini seam cover clip. Ref: BMP128, BMP0128, GFK7515, GHF1560, BMP128MS.

Fender flares as used on the ''20th Anniversary'' special models and virtually all of the later ''Special Edition'' classic Minis. Ref: GAW117, AJM1117, CZH4312, CZH4313, CZH4314, CZH4315.

Wood & Pickett-style flares look smooth and sleek and will cover most 10''-12'' wheels. Molded black ABS plastic. Ref: MS134.

Fiberglass ''Wood & Pickett''-style wide profile style flares look smooth and sleek and will cover most 10''-12'' wheels. Ref: MS133MS, MS133.

Reproduction of the factory Sports Pack fender flare as used from 1997-on; made of the same rubberized material with built-in mounting studs. Ref: ARCH001, AKSPTP.

Fiberglass flares, 1.75'' wide including lip; reproductions of the original Special Tuning ''Works''' arches.

A set of four (4) reproduction Group 2 fender flares, manufactured from fiberglass.

''Group 5'' 3'' arch set; the body line can be cut away or retained. Ideal for cars with wide 12'' and 13'' wheels. Ref: MS128, SBO0004.

Set of four Group 5-style fender flares; fiberglass finished in black gelcoat. 3.5'' wide, suitable for 6'' wide wheels. Ref: C-STN71, C-STN0071.

Set of four (4) fiberglass reproductions of the popular classic Mini Sports Pack fender flares. Ref: MS136.

Single flare from the classic Mini ''20th Anniversary''-type set. Ref: CZH4312, CZH4313, CZH4314, CZH4315.

Stainless steel headlamp ring, includes retaining screw; no drain holes. Ref: 500929, 500929MS, 54520650.

Premium chrome over stainless steel headlamp bezel. Made in the U.K. by Wipac. Ref: S5435, WIS5435, 500929W, DHF100060.

Black strip that runs from front to rear wheel arches on the plastic classic Mini ''20th Anniversary'' flares. Ref: CZH4316, FLARE001.

This trim can be used on the lower seam flange, where the body side mates with the sill (rocker) panel flange. Ref: GZF108MA, GZF108M.

Plastic stepped silver trim to cover the lower body seam at the rocker panel flange. Ref: GZF105MS, GZF0105E.

U-shaped chrome plastic molding that slips over the rocker panel flange seam. Ref: GZF107A, GZF0107A.

Special stud to allow attachment of exterior wood sections to classic Mini Estate models. These reproduction parts are identical in function to the original part.

Mounting stud for rubber Sports Pack flares. Coarse, self-tapping thread attaches to flare, M5.80 machine thread attaches to body.

Mounting stud for genuine Rover Sports Pack fender flares.

Nylock nut to fit the studs fitted to Sports Pack fender flares. Sold each.

A pair of chrome metal latches that are handy for fastening body panels. Pulls tight by puling the lever over center. Release by lifting the lever.

Small angled spacer to attach trim bar to bumper. Four (4) required per car.

If you have the Deluxe bumper setup, these are the bars that connect the overrider with the bumper bar. Now in polished stainless finish; choose right- or left-hand side.

Polished stainless-finish bars that connect the overrider with the bumper bar. Ref: 14A9919, 14A9920.

This square plastic insert accepts a #8 screw, and is used in various places on the classic Mini

Classic Mini Mk1 whisker clips for plastic side trim. Ref: ADU8629, RA608176, DMP0829.

This sheet metal cover is for cosmetics only, and conceals the radius arm bracket and grease nipple. Reproduction; choose right- or left-hand side.

Complete assembly for the red reflector used on the rear of the U.K.-made classic Mini Moke. Ref: BMK353.

Roll of plastic trim with shiny silver ''chrome'' insert to cover the rain gutter; works best with pre-1979 classic Minis which did not come with a rain gutter. Ref: MT632, YGA1106.

Reproduction roof gutter molding as used on classic Minis 1980-on; rigid steel core with black plastic covering. Ref: YGA1106, YGA1107.

Small metal clip used to join the two halves of the factory roof molding, or to join the two ends of the aftermarket trim. Ref: DBE10006PMD, YGA2387.

This small metal clip is used to join the two ends of the roof molding.

Rubber lower seam cover as originally made by Rover 1993-on. Ref: DDJ10002, ZUA000310.

Flexible black rubber side trim as used between Sports Pack wheel arches. Ref: DDJ10002, DDJ10002MS.

This triangular section rubber seal is used for seating the overriders on the bumpers and for certain fender (wheel arch) flares such as ''Wood & Picket'' design or ''Wide 25th Anniversary'' arches. Ref: 37H9871M.

Set of 16 black screws and washers, as supplied on SBO0041 ''Mini Special'' fender flare kit. Ref: GAW117S.

Reproduction metal finisher that covers the front external panel seams of the classic Mini. Ref: BMP127MS, BMP127.

Primed metal finisher that covers the front external panel seams of the classic Mini. Ref: BMP127, 14A9999, 14A9999/HTG.

Affordable reproduction seam covers, which do a good job at a modest price. Ref: BMP124, BMP125, BMP124MS, BMP125MS.

Reproduction seam cover for rear side of all classic Mini utility models. Ref: BMP131, BMP0131E.

Small seam cover behind the rear wheel. Ref: BMP129, 14A6795, BMP0129.

Rear step metal seam cover for the classic Mini Van, Estate, and Pickup. Ref: BMP130, 14A8368.

Premium seam cover, primed by the manufacturer. Ref: BMP124, BMP125, 14A6783, 14A6784.

Soft rubber seating strip for fender flares, installed between fender flare and steel body work for a finished appearance. Ref: SPL0060, SPL0059.